A customer called with a requirement that internal clients must be on different subnets depending on the building they are in. All access points are operating in local mode and will not be modified, and this is a single controller solution. Which design approach creates the desired result?

1. A. Create AP groups for each desired location, map the correct VLANs to the internal SSID, and add the access points for that location.
2. B. Create an SSID place it to the desired VLAN under WLANs and configure 802.1x in ISE to assign the correct VLAN based on the SSID from which the client is authenticating
3. C. Create FlexConnect groups, place the access points in, and set the correct VLAN to SSID mapping based on location.
4. D. Create mobility anchors for the SSID and on the controller under the internal SSID create a foreign map to the desired VLAN based on location.

Correct Answer: A
https://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-vlan/71477-ap-group-vlans-wlc.html

Multiple WLCs are implemented in a high-availability configuration in a mobility group. APs are deployed with only a primary controller assigned. By default, which mobility group member controller do the orphaned APs join in the event of a failed controller?

1. A. controller with the most available AP free license capacity
2. B. controller with the lowest percent of associated APs per license capacity
3. C. controller with the least CPU utilization over the last reporting period
4. D. controller with the least number of associated APs

Correct Answer: D
https://mrncciew.com/2013/04/07/ap-failover/

A network engineer is preparing for an office site survey with a height of 2.5 meters. Which three components are recommended to complete the survey? (Choose three.)

1. A. Use a battery pack to power APs
2. B. Use a drawing of the office space to draw AP and client placements.
3. C. Use DoS attack on APs while measuring the throughput.
4. D. Use APs with directional antennas.
5. E. Use APs with external antennas.
6. F. Use APs with built-in antennas.

Correct Answer: ABF
https://www.cisco.com/c/en/us/td/docs/wireless/technology/mesh/8-4/b_mesh_84/Site_Preparation_and_Plannin

Two cisco 5520 wireless LAN controllers are managing all access points throughout the network. The WLCs are in different locations to provide geographical redundancy a mobility group has been configured on both WLCs and has a UP status on both controllers. The Aps in location A are statically configured to use controller A as the primary and controller B as the secondary. If the WLC in location A goes offline. The Aps successfully join the WLC in location, but they do not fail over to their primary configured controller. Which configuration task fixes the issue?

1. A. Configure the WLC in location A as primary using the CAPWAP AP Controller IP Address command on all the location A Access points.
2. B. Use DHCP Option 43 and specify WLC in location A as primary.
3. C. Enable AP fallback globally on the WLC
4. D. Change the AP Failover Priority to critical.

Correct Answer: C

How should the concept of mobility domains and mobility groups be explained to a customer?

1. A. WLCs do not need to be in the same mobility domain to communicate with each other Mobility groups constrain the distribution of security context of a client and also constrain AP fail-over between controllers.
2. B. A mobility group does not constrain the distribution of security context of a client and also does not constrain AP fail-over between controllers when the WLCs are in the same mobility domain.
3. C. if WLCs are in same mobility domain, they communicate with each othe
4. D. Mobility groups constrain the distribution of security context of a client and also constrain AP fail-over between controllers.
5. E. If WLCs are in the same mobility domain, they communicate with each other bu
6. F. if an anchor WLC ® present, it must: be in the same mobility domain for communication to be possible.

Correct Answer: C